All categories
Number of views:

Electronic igniter thick film circuit

Retail price
Market price
range of working temperature:
Substrate material:
96% AL2O3 ceramic substrate
Conductor material:
Ag/Pd, strong conductor adhesion
Resistance material:
High-performance conductive material, stable resistance, low TCR value
Product description
Table Parameter

1. Product introduction:

Ceramic thick film circuit boards specially designed for various automobile and motorcycle igniters. These products are suitable for various automobile and motorcycle ignition systems. They are ideal ceramic circuit boards for electronic igniter control modules. They have good reliability and longevity. It has the advantages of long, stable use, convenient installation and welding.


2. Product features:

1. Reliable performance, stable input and output characteristics, high precision, low TCR, etc.

2. It has excellent heat dissipation performance and is suitable for the ignition system of automobile and motorcycle engines.

3. The product has long service life, good consistency, low line loss, and strong resistance to low electric wave interference

4. The product has excellent insulation, with insulation resistance greater than 1000M Ω (DC100V for 1 minute)

5. Good solderability and solder resistance, suitable for high-speed SMT patch processes such as reflow soldering


3. Product features:

1. Operating temperature range: -40℃~+125℃

2. Substrate material: 96% AL2O3 ceramic substrate

3. Conductor material: Ag/Pd, strong conductor adhesion

4. Resistance material: high-performance conductive material, stable resistance, low TCR value

5. Welding ability: the resistance change is less than 0.5% (265 ℃ soldering furnace, immersed in 10s, repeated 5 times to test the electric

Scan the QR code to read on your phone
We could not find any corresponding parameters, please add them to the properties table



Resistance range

0.2Ω 10M Ω

Resistance tolerance

Minimum ±0.5%


Temperature Coefficient of Resistance



±500PPM /℃

100 Ω≤R≤1MΩ

±250PPM /℃

Insulation resistance


Apply a 100V DC voltage between the substrate and the electrode , and test the insulation resistance value after 1 minute of electrification






Weldable area is greater than 95%

Dip the product into the inactive flux for about 2s , then remove the excess flux, immerse the product into the solder bath to a depth of 10mm , the solder bath temperature is 240℃±5℃ , the immersion time is 3s ±1 s , and the resistor is cleaned with solvent Flux residues on the film , observed under a magnifying glass of 10 times


Resistance to welding heat

No visible damage


Immerse the component into the solder tank to a depth of 10mm , the temperature in the solder tank is 270℃±5℃ , the immersion time is 10s ±1 s , and place it at room temperature for 1 to 2 hours. Clean the excess flux with a solvent, and then measure the resistance value

Rapid temperature change

No visible damage



Normal temperature (2 to 3 minutes ) -55°C±3°C for 30 minutes                125°C±3°C for 30 minutes Normal temperature (2 to 3 minutes ) , after 5 consecutive cycles from low temperature to high temperature , the component recovers for more than 1 hour under standard atmospheric conditions , Within 2 hours, measure the resistance value

Steady state damp heat

No visible damage


The component is maintained for 1000 hours in a humid heat test box with a temperature of 40℃±2℃ and a humidity of 90% to 95%

Solvent resistance

No visible damage


Dissolving solution: trichloroethylene, immersed in 10H±1H

Storage conditions

  Temperature: 5℃ 35℃ , relative humidity: 45% 70%RH

  Avoid storing in corrosive gas environment


Home         丨         About Us         丨         Product         丨         News         丨         Equipment         丨         Online Message         丨         Contact Us


iconAddress:No. 99 Mingtong Road, Zhouzhuang Town, Kunshan City, Suzhou, Jiangsu Province

We contact you



©2021 - Kunshan Fuye Electronics Co., Ltd